Recent content by FG Jeep

  1. F

    ac is charged, won't blow cold air?

    I work on ac pretty regularly. From what you are describing sounds like the compressor is short cycling. This is normally caused by low refrigerant charge. A few things about refrigerant. I assume that this is a r134a system. R12 follows the similarbguidelines but there are a few differences...
  2. F

    Upper control arm bolts

    I already have the 12mm stuff I was just curious if anybody had run 14mm on the upper.
  3. F

    Upper control arm bolts

    Link doesn't work. Upon going to page on my own it doesn't say anywhere in the description of it that these bushings allows for a larger bolt. From what is listed I would expect it to be a stock replacement keeping the 10mm bolt. More than likely I will go with 12mm or 1/2". But I'm curious...
  4. F

    Upper control arm bolts

    1/2" and 12mm are nearly the same size. I was more wondering if anybody has gone to a 14mm hardware which would be nearly the same as 9/16".
  5. F

    Upper control arm bolts

    I'm in the midst of upgrading some of the hardware in my suspension. Initially it started with a hardware upgrade and flex joint into the track bar. But I'm not a fan of the dinky m10 hardware for the upper control arms. I would like to step up to a M12 bolt for the uppers. It sounds as if m12...
  6. F

    1998 Grand Cherokee 5.9 Limited- Many modifications and new parts- MA- $4500

    Woa calm down man! I was just posting up what these things were going for when together. I'm not knocking the jeep at all I even said it has a ton of potential to be a very bad ass rig. The ad on this jeep alone is awesome. He posted every single issue with the jeep. Whoever buys this will know...
  7. F

    1998 Grand Cherokee 5.9 Limited- Many modifications and new parts- MA- $4500

    I agree it has a lot of good parts on/with it. However at the end of the day it needs a lot of axle work with mismatched gears and bracket work and what not. For a lot of people that is a bit of a turn off. The motor work is awesome. Swapping a 231 is a nice perk over the 249. But a 241or would...
  8. F

    1998 Grand Cherokee 5.9 Limited- Many modifications and new parts- MA- $4500

    Good luck with the sale. I sold my rust free fully functioning 124k mint pretty much stock slate 5.9l for 4800 2 years ago. I also know of a few nice 5.9 ltd's for sale in the 3800-5000 range. I think the price is highly optimistic.
  9. F

    my build begins

    Why drill the rear shock bolts when they break? I pop the nut serts with a air chisel. Probably 2 mins a side. Then feed a bolt through with a lock washer or weld it and your done. There is no reason to spend a hour drilling a rear shock nutsert out as opposed to hanging with your family.
  10. F

    DIY Bumper pics

    Rear bumper with tire carrier. I have some changes planned to the tire carrier portion as it tends to sag. I should of put the hinge portion on top of the bumper as opposed to hanging off the side. It does work well. Also the latch set up I chose is a pain in the but. I plan to change that to a...
  11. F

    ? for those that have built their own winch bumpers

    This is the bumper I built. It has a very recessed winch mount that sits in front of the crossmember. It has not effected my approach angle at all as it is tucked in tight to the front of the jeep. Since I relocated the solenoid box under hood it doesn't sit above the grille at all anymore. This...
  12. F

    what paint you guys using to paint an AXLE

    2 part bed liner for the underside is the way to go. My entire underside of my Xj is spray on 2 part black raptor liner. I primed it with chassis saver and then shot the raptor liner on top. I did this 4 years ago and it still looks like the day I did it. It's gone through 4 Chicago winters and...
  13. F

    what paint you guys using to paint an AXLE

    I use Raptor liner. Pretty much the only paints that can take chemical abuse are two part paints basically anything you have to mix a hardner into. There are a few exceptions (chassis saver comes to mind) but over all anything with a hardening agent will hold up to brake fluid (for short periods...
  14. F

    Zj pitman arm

    Yep that's kind of what I had decided. It isn't a big deal to do. I just was trying to avoid doing the job twice if possible.
  15. F

    Zj pitman arm

    I'm planning to go to the iro over the knuckle steering set up in the near future so I am keeping the factory links for the moment. I understand that everyone is a bit different in setup. However they all should respond similarly to changes in geometry. While the jeep cruises fine the angle of...
Back
Top